PHSOFT

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 allows you to easily open doors and start your vehicle. However, there are many reasons why the fob may stop functioning. This could be due where to get a fiat key cut a dead battery or water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat ducato key programming Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local locksmith (click here for Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is a dead battery. Key fobs of today have an operating range that is limited and must be within just a few inches of the vehicle to work. If you are further away from your car and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store, or online.

You can test the battery of your coin-cell by pressing the buttons while standing close to your Fiat 500. The parking lights should flash and the key fob will operate the lock and unlock switch.

If the key fob doesn't work after replacing the battery, it could be damaged by water that blocks it from connecting to the receiver module in your car. Water damage can happen in many ways, such as simply splashing or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If this does not work, you'll require your fob to be changed by an auto locksmith or a dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can be particularly harmful to the fob's circuit board and can cause it to short out and eventually die. If you get the fob wet, it's not an option but if you drop it into a cup of water or do not remember to take it out of your pants pocket before running the washer and you don't have a chance, don't give in.

First, remove the battery. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Next try the fob and see if it works. If the fob doesn't work, it may have to be programmed again. This is usually done by an auto locksmith or dealer.

If your key is a bit older and has not been programmed for your vehicle then you'll need to replace it completely. This is a simple procedure which can be accomplished by a professional automotive locksmith. The locksmith will need the key to be cut to match your car's ignition. They'll also need to reprogram the fob to the car's system. This is a cost-effective and quick process that can be completed within the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob won't be working is that it's simply out of range. The remote has a maximum range of 30 feet, which means when you're too far away from your vehicle it will not respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If your fob won't work after replacing the battery inside the coin, which is also known as a "button", "watch" or "button", it could be due to a problem with the circuit board inside. Reprogramming the fob typically resolves this issue. You can find the instructions on how to do this on the majority of automobiles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software or hardware issues. This could cause a significant problem, but you can frequently fix this issue by visiting an auto locksmith to Reprogram Fiat 500 Key Fob your fob. In certain instances, they may need to install the software again in your body control module as well.

Interference

In addition to a dead battery on a coin The key fob might not be able to receive or transmit a signal due to interference. This can occur when the keyfob is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob might not function because of a weak connection to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a defective receiver module on your 500. The receiver module, located beneath the dashboard, detects radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There's a simple method to reset the 500's on-board system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any residual electricity and restart the lost car keys fiat's computers, which could help get your key fob working again. If the issue continues, you should consult an expert technician. They will be able to determine the root of any issues.