PHSOFT

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat tipo key 500 Key Fob Won't Work

A fiat doblo key replacement 500 key fob allows you to easily open doors and start your vehicle. There are many reasons the fob may stop working. These include a dead battery damaged receiver module, water damage problems, and interference.

This listing is for a NEW replacement fiat key replacement cost Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob being inoperative. Modern key fobs have a restricted operating range, and should be within just a few feet of the vehicle to operate. If you are further away from your vehicle and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reliable brand, like Panasonic Duracell or Energizer. They can be found in your local hardware store, or on the internet.

You can test the battery in the coin-cell by pressing the buttons while you're standing close to your Fiat Remote Key 500. The car should flash its parking lights and the key fob should be able to operate the lock and unlock buttons.

If the fob's key doesn't function after replacing the battery, it could be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in a variety of ways, ranging from a light splash to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work, you will need to have your fob changed by an auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob in the ocean, or wash it in a washer. Saltwater can cause the circuit board to short and then die. The fob getting wet is not an option but if you drop it into a cup of water or fail to remove it from your pants pocket prior to running the washing machine do not give up hope.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Then test the fob to test if it works. If the fob doesn't work, it may have to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is newer and has never been programmed to your vehicle It is likely that it needs to be replaced completely. This is a simple procedure that can be completed by a professional locksmith for automotive use. The locksmith will require the key to be cut to match your car's ignition. The locksmith will also have to reprogram your fob into the car's system. This is a cheap and quick process that could be completed in the same day.

Receiver Module Issues

The 500 key fob could be inoperable because it's out of range. The remote typically has an area of 30 feet or less, and if it's too far away from your car it won't respond to your commands. You can fix this by moving the remote closer to your car until it responds.

If your fob doesn't work after you replace the coin battery, also known as a "button", "watch" or "button", it could be due to an issue with the circuit board inside. In most cases, reprogramming the fob will fix the issue. You can find the procedure for the majority of vehicles on YouTube or in the owner's manual.

It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they become loose, it may prevent your battery from being properly seated, causing your remote to malfunction.

In rare cases the fob could be out of sync with your vehicle because of software or hardware problems. This could be a huge trouble, but you could usually fix it by visiting an auto locksmith to reprogram your fob for you. In some instances it may be necessary to reinstall the software on your body control module as well.

Interference

In addition to a dead coin battery The key fob might not be able to receive or transmit an signal due to interference. This could happen if the key fob is near radio transmitters (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not function include a weak connection to the buttons or the internal chip, or water damage.

If the key fob has suddenly stopped working, out of the blue, or after trying everything you can do at home to resolve it e.g. replacing the battery, reprogramming, and using the spare key fob, you could have a faulty receiver module on your 500. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.

There is a straightforward method to reset the 500's on-board system including the keyfob. Disconnect the battery of 12 volts for approximately 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will erase any remaining electricity, and restart the computer in your car. This can help you get your key fob to work again. If the problem persists you should speak with an expert technician. They'll be able to determine the exact cause of your problems.